Asus Commando如何上533以上 1:1的基本概念

[S-03]

一直都有留意這編文章 可是一直看不到圖
有別的路徑可以看得到嗎?

 

[we88ca]

是不错的文章;cheer2;
板子嘛……;nq;
可惜好贵，我们这里要$269;em42;

 

[S-03]

是不错的文章;cheer2;
板子嘛……;nq;
可惜好贵，我们这里要$269;em42;

板子我買了 可惜沒看到狂少的圖 想看他的設定
我的ram u 板 跟他討論的都一樣 所以圖很有參考價值

 

[hyde211]

各位有Commando的板友，下面有BIOS設定選項
你們可以照你們的設定鍵入至"括號[]"內，再把問題提出來
這樣板上的超頻好手也比較好協助你們
PS: 順便附上所使用的 BIOS CPU RAM 顯卡;em03;

Extreme Tweaker

Over Clocking
____________________________________________________

AI Turing -------------------------------[Manual]
>CPU Frequency ------------------------[266]
>DRAM Frequency ----------------------[DDR2-667MHz]
>PCI Express Frequency ----------------[100]
>PCI Clock Frequency ------------------[33.33MHz]
>Spread Specttrum --------------------[Disabled]
____________________________________________________

Over Voltage
CPU VCore Voltage --------------------[1.5V]
FSB Termination Voltage ---------------[1.4V]
NB VCore -----------------------------[1.625V]
Menory Voltage -----------------------[2.4V]
DDRII Cannel A REF Voltage ------------[Auto]
DDRII Cannel B REF Voltage ------------[Auto]
DDRII Controller REF Voltage -----------[DDRII REF+10mv]
SB VCore(STAT,PCIE) -----------------[1.65V]
SB Chipset Voltage --------------------[1.125V]
____________________________________________________

ASUS C.G.I ---------------------------[Auto]
Static Read Control -------------------[Auto]
Configure DRAM Timing by SPD --------[Disabled]
>>DRAM CAS# Latency ---------------[4]
>>DRAM RAS# to CAS# Delay ---------[4 DRAM Clocks]
>>DRAM Precharge -------------------[4 DRAM Clocks]
>>DRAM Activate to Precha -----------[12 DRAM Clocks]
>>DRAM Write Recovery Time ---------[2 DRAM Clocks]
>>DRAM TRFC ------------------------[30 DRAM Clocks]
>>DRAM TRRD ------------------------[9]
>>Rank Write to Read Delay -----------[9]
>>Rank to Precharge Delay ------------[9]
>>Write to Precharge Delay ------------[9]
____________________________________________________

Advanced
Modify Ratio Support ------------------[Enabled]
>>Ratio CMOS Setting -----------------[6]
C1E Support --------------------------[Disabled]
Max CPUID Value Limit -----------------[Disabled]
Vanderpool Technology ----------------[Disabled]
CPU TM function: ---------------------[Disabled]
Execute Disable Bit --------------------[Disabled]
PECI ----------------------------------[Disabled]
____________________________________________________

--
剩下就交給專業的:D [逃~~]

 

[JCornell]

不知狂大可否分享Commando + QX6700 上 400*9 的調教 ...
在Commando都常藍底白字, 連FSB300都不穩 ;oq;
400*9把FSB&北橋電壓拉高, 進系統了, 但不穩 ...

此U在P5B-D都輕鬆上的 ... 很穩 ... ;face12;

 

[S-03]

commando 0803
E6600
TEAM XTREEM DDR2-1000 CL5 5-5-5-15
行 orthos @ stress cpu 沒問題 行stress cpu and ram就stop
但ram在memtest pass 150%
想先找出cpu在那個頻穩定才再超ram的
和想跟狂少的設定跑一下看看有什麼不同-可是看不到圖;em42;
以下我setting 請提點一下

Over Clocking
____________________________________________________

AI Turing -------------------------------[Manual]
>CPU Frequency ------------------------[380]
>DRAM Frequency ----------------------[DDR2-760MHz]
>PCI Express Frequency ----------------[100]
>PCI Clock Frequency ------------------[33.33MHz]
>Spread Specttrum --------------------[Disabled]
____________________________________________________

Over Voltage
CPU VCore Voltage --------------------[1.325V]
FSB Termination Voltage ---------------[1.4V]
NB VCore -----------------------------[1.35V]
Menory Voltage -----------------------[1.95V]
DDRII Cannel A REF Voltage ------------[DDRII REF]
DDRII Cannel B REF Voltage ------------[DDRII REF]
DDRII Controller REF Voltage -----------[DDRII REF+10mv]
SB VCore(STAT,PCIE) -----------------[1.55V]
SB Chipset Voltage --------------------[1.125V]
____________________________________________________

ASUS C.G.I ---------------------------[Auto]
Static Read Control -------------------[Auto]
Configure DRAM Timing by SPD --------[Disabled]
>>DRAM CAS# Latency ---------------[4]
>>DRAM RAS# to CAS# Delay ---------[4 DRAM Clocks]
>>DRAM Precharge -------------------[4 DRAM Clocks]
>>DRAM Activate to Precha -----------[5 DRAM Clocks]
>>DRAM Write Recovery Time ---------[6 DRAM Clocks]
>>DRAM TRFC ------------------------[25 DRAM Clocks]
>>DRAM TRRD ------------------------[4]
>>Rank Write to Read Delay -----------[9]
>>Rank to Precharge Delay ------------[4]
>>Write to Precharge Delay ------------[9]
____________________________________________________

Advanced
Modify Ratio Support ------------------[Enabled]
>>Ratio CMOS Setting -----------------[9]
C1E Support --------------------------[Disabled]
Max CPUID Value Limit -----------------[Disabled]
Vanderpool Technology ----------------[Disabled]
CPU TM function: ---------------------[Disabled]
Execute Disable Bit --------------------[Disabled]
PECI ----------------------------------[Disabled]
____________________________________________________

 

[JCornell]

不知狂大可否分享Commando + QX6700 上 400*9 的調教 ...
在Commando都常藍底白字, 連FSB300都不穩 ;oq;
400*9把FSB&北橋電壓拉高, 進系統了, 但不穩 ...

此U在P5B-D都輕鬆上的 ... 很穩 ... ;face12;

以上沒問題了, 板子烙賽, 換板子就ok了 ;smash; ... 難怪這樣難搞, 就是不會穩 ... ;em28;

 

[hyde211]

commando 0803
E6600
TEAM XTREEM DDR2-1000 CL5 5-5-5-15
行 orthos @ stress cpu 沒問題 行stress cpu and ram就stop
但ram在memtest pass 150%
想先找出cpu在那個頻穩定才再超ram的
和想跟狂少的設定跑一下看看有什麼不同-可是看不到圖;em42;
以下我setting 請提點一下
...

1.如要先找CPU穩定，建議把ram調鬆，5-5-5-15[其他時序AUTO]，確定排除ram因素

2."行 orthos @ stress cpu 沒問題 行stress cpu and ram就stop "，很明顯的問題在ram，RAM及NB電壓在加一點[記得拿風扇吹一下喔 ]

 

[S-03]

1.如要先找CPU穩定，建議把ram調鬆，5-5-5-15[其他時序AUTO]，確定排除ram因素

2."行 orthos @ stress cpu 沒問題 行stress cpu and ram就stop "，很明顯的問題在ram，RAM及NB電壓在加一點[記得拿風扇吹一下喔 ]

那我再測一下
多謝指點

 

[natppdd]

恩....看到這篇,突然有點感觸

之前用P5B-D 參數少,懶人超一下就E6300 460*7穩

最近換Striker ,參數一堆,環環相扣,怎麼調怎麼不穩

目前還不得其要領中..........................;oq;

不過玩OC不就是好玩在這裡

現在看到這篇, 似乎有點頭緒, 繼續TRY TRY;ranger;