我的Maximus Formula
- 主題發起人 andy5785
- 開始日期
把下面這些 改這樣
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.67x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
以按照上面這位大大的指導設定
感謝各位大大們的指導,現可以500外頻開機了,可是倍頻只能到6,我只要用到500X6.5就不能開機了....
lianen
進階會員
- 已加入
- 1/16/08
- 訊息
- 423
- 互動分數
- 0
- 點數
- 16
這樣就滿足了嗎;em03; 嘎~~電落企~~~;em25;
Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Control [Manual]
Ratio CMOS Setting: [8]
FSB Frequency [500]
FSB Strap to North Bridge [Auto]
PCIE Frequency [100]
DRAM Settings: DDR2(MF)
DRAM Frequency [選1201]>>>>不開再選1000 跑1:1 (1201是5:6)
DRAM Command Rate [AUTO]
DRAM Timing Control [Manual]
CAS# Latency [5]
RAS# to CAS Delay [5]
RAS# Precharge [5]
RAS# Active Time [12]>>>不開 再調15或10或18
RAS# To Ras# Delay [4]>>>不開 調3
Row Refresh Cycle Time [30]>>不開調35或42
Write Recovery Time [4]>>不開調6
Read To Precharge Time [4]不開調5
Read To Write Delay(S/D) [8] 也可以弄AUTO
Write To Read Delay(S) [3] 也可以弄AUTO
Write To Read Delay(D) [5] 也可以弄AUTO
Read To Read Delay(S) [4] 也可以弄AUTO
Read To Read Delay(D) [6] 也可以弄AUTO
Write To Write Delay(S) [4] 也可以弄AUTO
Write To Write Delay(D) [6] 也可以弄AUTO
DRAM Static Read Control [Disabled]
Ai Clock Twister [Strong]
Transaction Booster [Enabled]
Boost Level [0]先從0開始慢慢試到1 1是比較理想 先從0開始
Voltage Settings:
CPU Voltage [1.49375v]>>不開再調高 可以開機後在慢慢往下修正
CPU PLL Voltage [Auto]
North Bridge Voltage [1.71v]
DRAM Voltage [2.46v]>>跑1200不開再修正到2.48 (往上到2.6就停手吧)
FSB Termination Voltage [1.46v]
South Bridge Voltage [Auto]
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.67x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
NB LED Selection [NB Volt]
SB LED Selection [SB Volt]
CPU LED [CPU Volt]
Voltiminder LED [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Configuration 頁面設定 這裡通通給它[Disabled]
CPU Ratio Control [Manual]
C1E Support [Disabled]
CPU TM function: [Disabled]
Vanderpool Technology [Disabled]
Execute Disable Bit [Disabled]
Max CPUID Value Limit [Disabled]
Intel(R) SpeedStep(tm) Tech. [Disabled]
接下來 在記憶體 參數方面 就要自己摸索了唷 能說的不多了^^
建議先以1:1 試過各種搭配 再去試5:6 怕你的RAM 上不去
Ai Overclock Tuner [Manual]
OC From CPU Level Up [Auto]
CPU Ratio Control [Manual]
Ratio CMOS Setting: [8]
FSB Frequency [500]
FSB Strap to North Bridge [Auto]
PCIE Frequency [100]
DRAM Settings: DDR2(MF)
DRAM Frequency [選1201]>>>>不開再選1000 跑1:1 (1201是5:6)
DRAM Command Rate [AUTO]
DRAM Timing Control [Manual]
CAS# Latency [5]
RAS# to CAS Delay [5]
RAS# Precharge [5]
RAS# Active Time [12]>>>不開 再調15或10或18
RAS# To Ras# Delay [4]>>>不開 調3
Row Refresh Cycle Time [30]>>不開調35或42
Write Recovery Time [4]>>不開調6
Read To Precharge Time [4]不開調5
Read To Write Delay(S/D) [8] 也可以弄AUTO
Write To Read Delay(S) [3] 也可以弄AUTO
Write To Read Delay(D) [5] 也可以弄AUTO
Read To Read Delay(S) [4] 也可以弄AUTO
Read To Read Delay(D) [6] 也可以弄AUTO
Write To Write Delay(S) [4] 也可以弄AUTO
Write To Write Delay(D) [6] 也可以弄AUTO
DRAM Static Read Control [Disabled]
Ai Clock Twister [Strong]
Transaction Booster [Enabled]
Boost Level [0]先從0開始慢慢試到1 1是比較理想 先從0開始
Voltage Settings:
CPU Voltage [1.49375v]>>不開再調高 可以開機後在慢慢往下修正
CPU PLL Voltage [Auto]
North Bridge Voltage [1.71v]
DRAM Voltage [2.46v]>>跑1200不開再修正到2.48 (往上到2.6就停手吧)
FSB Termination Voltage [1.46v]
South Bridge Voltage [Auto]
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.67x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
NB LED Selection [NB Volt]
SB LED Selection [SB Volt]
CPU LED [CPU Volt]
Voltiminder LED [Enabled]
CPU Spread Spectrum [Disabled]
PCIE Spread Spectrum [Disabled]
CPU Configuration 頁面設定 這裡通通給它[Disabled]
CPU Ratio Control [Manual]
C1E Support [Disabled]
CPU TM function: [Disabled]
Vanderpool Technology [Disabled]
Execute Disable Bit [Disabled]
Max CPUID Value Limit [Disabled]
Intel(R) SpeedStep(tm) Tech. [Disabled]
接下來 在記憶體 參數方面 就要自己摸索了唷 能說的不多了^^
建議先以1:1 試過各種搭配 再去試5:6 怕你的RAM 上不去
;cheer2; ;cheer2; 谢谢！谢谢！你和你的发现都好神奇。
本来我的MF只能475开机，有时候还进不了系统，加压、南北桥拆下来换散热硅脂，所有看到的方法都试验过了，没有任何改进，在我绝望之际（最近正在等X48上市想换掉），看到您的发现，我怀着死马当作活马医的心情试验了一下，只是把DRAM 设置为auto，一次轻松开机。
;shakehand ;shakehand
说实话，我这块板子真是不错，在众多人大骂MF掉压之际，我得居然不掉压。现在连高FSB的问题也解决了。看来没有换X48的必要了。
我来告诉你怎么上550FSB 和你一样的主板！我的E8200
详细配置
CPU：INTEL E8200FAN：ASUS V70
主板：ASUS MAXIMUS FORMULA(X38)
内存：MT DDR2-6400（默认）1G*2
硬盘：ST250G 7200.10
显卡 ：影驰8800GS骨灰魔魂0.8ns 600/2000
电源：航嘉宽幅王350W
机箱：TT海啸侧透
键鼠：ZIPPY全铝合金无线套
光存储：PIONNER DVD-RW和DVD-ROM
LCD：三星961GW
CPU Feature:
Ai Overclock Tuner [Manual]
CPU Ratio Control [Manual]
Ratio CMOS Setting: [8]
FSB Frequency [550]
FSB Strap to North Bridge [Auto]
PCIE Frequency [110 for 3D; 100 for normal]
DRAM Settings: DDR2
DRAM Frequency DRAM Command Rate [Auto]
DRAM Timing Control [Manual]
CAS# Latency [4]
RAS# to CAS Delay [4]
RAS# Precharge [4]
RAS# Active Time [12]
RAS# To Ras# Delay [4]
Row Refresh Cycle Time [42]
Write Recovery Time [6]
Read To Precharge Time [3]
Read To Write Delay(S/D) [8]
Write To Read Delay(S) [3]
Write To Read Delay(D) [5]
Read To Read Delay(S) [4]
Read To Read Delay(D) [6]
Write To Write Delay(S) [4]
Write To Write Delay(D) [6]
DRAM Static Read Control [Disabled]
Ai Clock Twister [Auto]
Transaction Booster [Enabled]
Boost Level [0]
Voltage Settings:
CPU Voltage [1.45v~1.55v]
CPU PLL Voltage [1.6~1.7]
North Bridge Voltage [1.61v~1.7v]
DRAM Voltage [2.32v~2.46v]
FSB Termination Voltage [1.46~1.5v]
South Bridge Voltage [Auto]
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.63x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
详细配置
CPU：INTEL E8200FAN：ASUS V70
主板：ASUS MAXIMUS FORMULA(X38)
内存：MT DDR2-6400（默认）1G*2
硬盘：ST250G 7200.10
显卡 ：影驰8800GS骨灰魔魂0.8ns 600/2000
电源：航嘉宽幅王350W
机箱：TT海啸侧透
键鼠：ZIPPY全铝合金无线套
光存储：PIONNER DVD-RW和DVD-ROM
LCD：三星961GW
CPU Feature:
Ai Overclock Tuner [Manual]
CPU Ratio Control [Manual]
Ratio CMOS Setting: [8]
FSB Frequency [550]
FSB Strap to North Bridge [Auto]
PCIE Frequency [110 for 3D; 100 for normal]
DRAM Settings: DDR2
DRAM Frequency DRAM Command Rate [Auto]
DRAM Timing Control [Manual]
CAS# Latency [4]
RAS# to CAS Delay [4]
RAS# Precharge [4]
RAS# Active Time [12]
RAS# To Ras# Delay [4]
Row Refresh Cycle Time [42]
Write Recovery Time [6]
Read To Precharge Time [3]
Read To Write Delay(S/D) [8]
Write To Read Delay(S) [3]
Write To Read Delay(D) [5]
Read To Read Delay(S) [4]
Read To Read Delay(D) [6]
Write To Write Delay(S) [4]
Write To Write Delay(D) [6]
DRAM Static Read Control [Disabled]
Ai Clock Twister [Auto]
Transaction Booster [Enabled]
Boost Level [0]
Voltage Settings:
CPU Voltage [1.45v~1.55v]
CPU PLL Voltage [1.6~1.7]
North Bridge Voltage [1.61v~1.7v]
DRAM Voltage [2.32v~2.46v]
FSB Termination Voltage [1.46~1.5v]
South Bridge Voltage [Auto]
Loadline Calibration [Enabled]
CPU GTL Reference [0.63x]
North Bridge GTL Reference [0.63x]
DDR2 Channel A REF Voltage [Auto]
DDR2 Channel B REF Voltage [Auto]
DDR2 Controller REF Voltage [DDR2_REF]
SB 1.5V Voltage [Auto]
最後編輯：
今天跑去買了一隻JETRAM DDR2-800-2G 擔心買回來超不上去,所以只好先買一隻試試,後來在bios上直接設定,500X8 輕鬆開機,之前的KINGMAX DDRII 1066/1GB 竟然超不到1066..有夠悶的,頂多超到1033,1034就不開機囉!電壓加到2.6還是一樣,而且奇怪的是,設回DDR2-1000,500X6才能開,500X6.5就開不了機囉!,換了這創見的記憶體,500X8輕鬆開機,試過記憶體極限大約在1100,在上去就不行了,也試過500X9可開機,確無法進入XP,目前穩定的使用500X8=4G , 記憶體DDR2-1000 不囉嗦,看圖吧^^PS:感謝指導小弟的幾位大大,^^在此致上最真誠的謝意,也讓我瞭解到,想玩超頻,記憶體的體質是很重要的!;cheer2;
