補上大圖
這個是534的
有人叫我照幾張上來 以下看看
變型的顯示卡
改過的LSATA 那條線一邊的被我去掉很多多
對不起用手機照的 有一點難看請見諒
在補充一下 bios 1703
有人PM我要設定
我像磁碟機關 跟沒用IDE 關 1394也關 其他大多預設吧 華碩那些 什麼功能也沒裝
AI Overclock tuner: Manual
CPU Ratio Setting: 7.5
FSB Strap to North Bridge: auto
FSB Frequency: 533 我好像有多+1 因為FSB會掉1
RAM的體質很重要哦 ram上不去 不能穩定 cpu 主機版在強也沒用
PCI-E Frequency: 100
DRAM Frequency: 1066~1068
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 5
DRAM RAS# to CAS# Delay: 5
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 15
RAS# to RAS# Delay : A
Row Refresh Cycle Time: A
Write Recovery Time:A
Read to Precharge Time: A
2nd Information :
READ to WRITE Delay (S/D): A
Write to Read Delay (S): A
WRITE to READ Delay (D): A
READ to READ Delay (S): A
READ to READ Delay (D): A
WRITE to WRITE Delay (S): A
WRITE to WRITE Delay (D): A
3rd Information :
WRITE to PRE Delay: A
READ to PRE Delay: A
PRE to PRE Delay: A
ALL PRE to ACT Delay: A
ALL PRE to REF Delay: A
DRAM Static Read Control: A
DRAM Read Training: A
MEM. OC Charger: A
AI Clock Twister: A
AI Transaction Booster: A
CPU Voltage: 1.1875V 實際上主機版是跑1.16v
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: A
FSB Termination Voltage: A
DRAM Voltage: 1.90
NB Voltage: 1.26
NB GTL Reference: AUTO
SBridge Voltage: 1.10V
PCIE SATA Voltage: 1.50V
Load Line Calibration: A
上面這個有人說不要開 但實際上不開的話 掉壓很嚴重 所以我選擇是開
看看我的電壓 就應該有人知道我為什麼會開了
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
以下這二個我不用一樣系統還真的不穩
CPU Clock Skew : 200ps
NB Clock Skew : 200ps
Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel® Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: E
(怕cpu 過熱 南部夏天很熱的 昨天測58x時有燒到破百 不過那時是老bios 也有可能跟軟體撞到
還有看到 -北橋 -cpu的溫度
Execute Disable Bit: Disabled
