[OPB 2008cbb oc team]P45上不了600?那就奇嚕,看Asus p5q dx如何叱吒風雲
- 主題發起人 狂少
- 開始日期
请问狂少，我入手了p5q3dx，400外频能进系统，但是只要一重起就会有一次断电，然后屏幕就一直黑了，不知道为什么。
我的设置如下
JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 6
FSB Strap to North Bridge: auto
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: 1600
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 7
DRAM RAS# to CAS# Delay: 6
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 24
RAS# to RAS# Delay : A
Row Refresh Cycle Time: A
Write Recovery Time:A
Read to Precharge Time: A
2nd Information :
READ to WRITE Delay (S/D): A
Write to Read Delay (S): A
WRITE to READ Delay (D): A
READ to READ Delay (S): A
READ to READ Delay (D): A
WRITE to WRITE Delay (S): A
WRITE to WRITE Delay (D): A
3rd Information :
WRITE to PRE Delay: A
READ to PRE Delay: A
PRE to PRE Delay: A
ALL PRE to ACT Delay: A
ALL PRE to REF Delay: A
DRAM Static Read Control: D
DRAM Read Training: D
MEM. OC Charger: E
AI Clock Twister: A
AI Transaction Booster: A
Common Performance Level :
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.325
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52V
FSB Termination Voltage: 1.22V
DRAM Voltage: 1.92V
NB Voltage: 1.40v
NB GTL Reference: AUTO
SBridge Voltage: 1.10V
PCIE SATA Voltage: 1.50V
Load Line Calibration: enable
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : 300ps
NB Clock Skew : 100ps
Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel? Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
我的设置如下
JumperFree Configuration Settings
AI Overclock tuner: Manual
CPU Ratio Setting: 6
FSB Strap to North Bridge: auto
FSB Frequency: 400
PCI-E Frequency: 100
DRAM Frequency: 1600
DRAM CLK Skew on Channel A1: AUTO
DRAM CLK Skew on Channel A2: AUTO
DRAM CLK Skew on Channel B1: AUTO
DRAM CLK Skew on Channel B2: AUTO
DRAM Timing Control: Manual
1st Information :
CAS# Latency: 7
DRAM RAS# to CAS# Delay: 6
DRAM RAS# Precharge: 5
DRAM RAS# Activate to Precharge: 24
RAS# to RAS# Delay : A
Row Refresh Cycle Time: A
Write Recovery Time:A
Read to Precharge Time: A
2nd Information :
READ to WRITE Delay (S/D): A
Write to Read Delay (S): A
WRITE to READ Delay (D): A
READ to READ Delay (S): A
READ to READ Delay (D): A
WRITE to WRITE Delay (S): A
WRITE to WRITE Delay (D): A
3rd Information :
WRITE to PRE Delay: A
READ to PRE Delay: A
PRE to PRE Delay: A
ALL PRE to ACT Delay: A
ALL PRE to REF Delay: A
DRAM Static Read Control: D
DRAM Read Training: D
MEM. OC Charger: E
AI Clock Twister: A
AI Transaction Booster: A
Common Performance Level :
Pull-In of CHA PH1: DISABLED
Pull-In of CHA PH2: DISABLED
Pull-In of CHA PH3: DISABLED
Pull-In of CHA PH4: DISABLED
Pull-In of CHB PH1: DISABLED
Pull-In of CHB PH2: DISABLED
Pull-In of CHB PH3: DISABLED
Pull-In of CHB PH4: DISABLED
CPU Voltage: 1.325
CPU GTL Voltage Reference (0/2): AUTO
CPU GTL Voltage Reference (1/3): AUTO
CPU PLL Voltage: 1.52V
FSB Termination Voltage: 1.22V
DRAM Voltage: 1.92V
NB Voltage: 1.40v
NB GTL Reference: AUTO
SBridge Voltage: 1.10V
PCIE SATA Voltage: 1.50V
Load Line Calibration: enable
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Clock Skew : 300ps
NB Clock Skew : 100ps
Advance CPU Settings
CPU Ratio Setting: Manual
CPU VID: Default
C1E Suppport: Disabled
Max CPUID Value Limit: Disabled
Intel? Virtualization Tech: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
- 已加入
- 9/18/03
- 訊息
- 14,396
- 互動分數
- 2
- 點數
- 0
s815026920
幸運女神愛你喔
- 已加入
- 7/24/07
- 訊息
- 607
- 互動分數
- 0
- 點數
- 16
- 年齡
- 41
狂老大.....我發現一件事情喔......我手上3塊p35 都是一樣的問題....500外頻全部都是依樣被秒殺.....................我覺得應該讀不是u的問題 是版子........
