小弟有幸入手C大的QX9650 C大的測試連結
搞了張ASUS RE來玩玩
目前以400x10機殼內穩定運作中
只是電壓方面小弟不太滿意
C大以1.296v的電壓就能跑400x10
而在小弟這版子上卻要1.4125v才能穩定
兩張板子真的會差這麼多嗎?
以下是小弟的硬體
CPU - QX9650 C1
MB- Rampage Extreme 0801
Ram - G-Skill 1600HZ 1Gx2
VGA - 麗臺9800GTX+
POWER - 保銳 720W
以下為小弟BIOS的大致設定
FSB Frequency: 400
CPU Configuration
CPU Ratio Setting: 10.0
C1E Support: Disabled
CPU TM Function: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: Auto
PCIE Frequency: 100
DRAM Frequency: 1600Mhz
DRAM Command Rate: 1N
DRAM Timing Control: Manual
1st Information:
CAS# Latency: 7
RAS# to CAS# Delay: 7
RAS# Pre Time: 7
RAS# ACT Time: 18
RAS# To RAS# Delay: 6
REF Cycle Time: 88
WRITE Recovery Time: 10
READ to Pre Time: 6
2nd Information :
READ to WRITE Delay (S/D): 10
WRITE to READ Delay (S): 5
WRITE to READ Delay (D): 6
READ to READ (S): 5
READ to READ (D): 7
WRITE to WRITE (S): 5
WRITE to WRITE (D): 7
3RD Information:
WRITE to PRE Delay: 21
READ to PRE Delay: 8
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 9
ALL PRE to REF Delay: 9
DRAM Static Read Control: Enabled
DRAM Dynamic Write Control: Enabled
DRAM Skew Control
DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto
Ai Clock Twister: Lighter
Ai Transaction Booster: Manual
Common Performance Level: 08
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
EPU II Phase Control: Auto
Load-Line Calibration: Enabled
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.25v
CPU GTLVerf (0): Auto
CPU GTLVerf (1): Auto
CPU GTLVerf (2): Auto
CPU GTLVerf (3): Auto
NB GTLVerf: Auto
North Bridge Voltage: 1.35v
DRAM Voltage: 1.9v
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
搞了張ASUS RE來玩玩
目前以400x10機殼內穩定運作中
只是電壓方面小弟不太滿意
C大以1.296v的電壓就能跑400x10
而在小弟這版子上卻要1.4125v才能穩定
兩張板子真的會差這麼多嗎?
以下是小弟的硬體
CPU - QX9650 C1
MB- Rampage Extreme 0801
Ram - G-Skill 1600HZ 1Gx2
VGA - 麗臺9800GTX+
POWER - 保銳 720W
以下為小弟BIOS的大致設定
FSB Frequency: 400
CPU Configuration
CPU Ratio Setting: 10.0
C1E Support: Disabled
CPU TM Function: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: Auto
PCIE Frequency: 100
DRAM Frequency: 1600Mhz
DRAM Command Rate: 1N
DRAM Timing Control: Manual
1st Information:
CAS# Latency: 7
RAS# to CAS# Delay: 7
RAS# Pre Time: 7
RAS# ACT Time: 18
RAS# To RAS# Delay: 6
REF Cycle Time: 88
WRITE Recovery Time: 10
READ to Pre Time: 6
2nd Information :
READ to WRITE Delay (S/D): 10
WRITE to READ Delay (S): 5
WRITE to READ Delay (D): 6
READ to READ (S): 5
READ to READ (D): 7
WRITE to WRITE (S): 5
WRITE to WRITE (D): 7
3RD Information:
WRITE to PRE Delay: 21
READ to PRE Delay: 8
PRE to PRE Delay: 1
ALL PRE to ACT Delay: 9
ALL PRE to REF Delay: 9
DRAM Static Read Control: Enabled
DRAM Dynamic Write Control: Enabled
DRAM Skew Control
DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto
Ai Clock Twister: Lighter
Ai Transaction Booster: Manual
Common Performance Level: 08
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
EPU II Phase Control: Auto
Load-Line Calibration: Enabled
CPU PLL Voltage: 1.54
FSB Termination Voltage: 1.25v
CPU GTLVerf (0): Auto
CPU GTLVerf (1): Auto
CPU GTLVerf (2): Auto
CPU GTLVerf (3): Auto
NB GTLVerf: Auto
North Bridge Voltage: 1.35v
DRAM Voltage: 1.9v
NB DDRVref: Auto
DDR3 ChannelA Vref: Auto
DDR3 ChannelB Vref: Auto
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled